- Turbine Turbocharger
- Oil cooled only
- 6 blade propeller
- Compressor Specs :
4"""" Compressor Inlet
2.226"""" or 56.55mm Inducer
2.552"""" or 74.83mm Major
Compressor .70 A.R.
Compressor 75 Trim
- Turbine Specs :
Twin Entry Type
11 Blade Type
Turbine .84 A.R.
Turbine 60 Trim
2.894"""" or 73.50mm Major
2.275"""" or 57.78mm Minor
- Made to use external wastegate
- Uses T3 Exhaust flange (Dual Entry)
- Fits with any aftermarket pipe of 4" diameter
- Plate and Mesh made out of high quality stainless steel to keep it from rusting on cold air or high moisture locations
- Includes high quality micro cotton filter that can be easily washed with soap and water. (No need to buy special oils or special solvents like the competition filters)
- Double Stainless Steel Mesh reinforced
- Best used on highly modified or turbocharged vehicles where higher air flow can be obtained
- Great for cars with very limited space to place a filter.
- Work with: 4" Outer Diameter pipe , Short Ram Intake , Cold Air Intake , Turbocharger , Supercharger
Heat Shield Cover:
- High quality stainless steel mesh wire inner lining w/ silicone impregnated fiber glass material
- Heavy duty turbo blanket wrapped around
- Stainless rivets and springs
- Helps decrease turbo heat from spreading into the engine bay
- Can hold up to 2,000 degree Fahrenheit
- 3.6"" Width
Oil Return Drain Line:
- Oil Drain/Return Line
- 22"" Stainless steel hose, braided for heat and pressure resistance, strength and durability
- Oil Return Line made for turbo
- Helps circulate oil from the turbo to the oil pan
- T3 Based Turbo Charger Only (Works only on Metal Oil Pans)
Oil Line Kit:
- Made out of high quality stainless steel.
- Oil feed line for turbo.
- 1/8 size oil feedline with -4an fitting.
- Threads in m10x1.5 turbo restricter plate with threaded 1/8npt on top, so it will allow you to use a 90 or straight -4an fitting.
- By using this oil line kit,it will allow you to convert or replace your oem line. 36"" long,1/8npt male end and -4female end.
- Adapter is made out of high quality steel,and supply 90 and straight -4an fitting.
- This line is made for t3 based center sections using m10x1.5 thread
Digital Turbo Boost Controller:
- Built in Turbo timer ( Auto and Manual )
- 2 Channel output, activate NITROUS or INTERCOOLER SPRAYER
- Features built in absolute pressure sensor
- Display will allow you to see real time voltage, boost, vacuum and high and low setting
- Will allow to run 2 boost setting either High and Low boost settings, adjustable to users preference.
- Adjustable gain (how slow or quickly the wastegate opens). Records highest boost pressure reached and also last peak boost while driving, Peak boost warning.
- The 12v 2 channel options on our kits is a great feature to allow you to get more out of your car.You can control systems such as nitrous or an intercooler sprayer all based off of boost pressures.
- With the turbo timer functions, you can select with this auto or manual settings that you can program.Either allow the boost controller to figure how long the car should run depending on boost levels reached during the prior driving select your preset run time.
- The controller has a function built in with an audible warning to notify the driver without have to see the boost gauge that the car has exceeded the set highest boost setting.
- Along with our kit, you will see below we have a full instruction packet that will go along with this.This will detail the full install process and basic knowledge of the way the system works is necessary to complete the install.Everything is included as you can see from the photo below to get the kit installed
- Wastegate has successfully addressed these issues by optimizing valve lift and the flow path through the body.
Works with single or twin turbos, and runs internal or external wastegates up to 25.5PSI. This has a high quality internal pressure sensor, and a high quality fast response boost control solenoid
- Instructions are included!
JDM 38mm Turbo External Wastegate:
- 17-7 PH Stainless Steel actuator spring gives consistent pressure at high temperature, resist "relaxing" at temperature to 900F (483C).
- High temperature silicone reinforced actuator diaphragm.
- High temp alloy is used for valve and 347SS valve housing will offer longer product life compared to competing designs.
- External wastegates are commonly used for regulating boost levels more precisely than internal wastegates in high power applications, where high boost levels can be achieved.
- Horizontal Ribbed designed that makes it highly resistant to heat.
- This wastegate allows you to change PSI by simply changing the Wastegate Springs. (Note: check out our ebay store for other PSI springs)
- Mating weld flanges are 304L.
- Comes with a spring around 8psi
- Used with any turbo manifold with 35/38mm external wastegate flange.